JOBO AG

Service Analog

Instructions for the CPA-2 and CPP-2 Processors

[CPP-2]

Starting in 1995, JOBO has modified both the CPA-2 and CPP-2 processors. Units obtained after this transition (serial number 22000 and greater for both models), use a different rotation motor, magnet or cog, and associated circuit boards. These processors can be identified by examining the rotation motor shaft. The newer units have a tapered shaft, threaded on the inside. Previous units have a cylindrical, non-tapered shaft that is not threaded. When replacing rotation motors or circuit boards, be sure to determine which version you have before obtaining these parts. The new motor magnet or motor cog is tapered to accommodate the tapered shaft. These motor magnets or cogs are secured with a hex-headed screw. (The older version of drive magnets and cogs are attached with a slot headed screw.) Both the magnets for the tanks and the cogs for the lids have not changed. No other components have been replaced with this modification. For clarity, the newer components are identified in the list below with a star '*'. (The star is not part of the part identification number or description.)

WARNING: If you are unsure as to the appropriate selection of replacement parts, contact JOBO for assistance. Use of inappropriate replacement parts may damage your processor or lessen the performance or life of the processor.

Parts for the Motor Head:

# 13013 Motor Head Nut (black brass thumbnut)
#13068 Brass Adapter (CPP-2 only, Cold-Water Solenoid Valve, 3/4" hose)
#15157 Washer for Brass Adapter (CPP-2 only, Cold-Water Solenoid Valve, 3/4" hose)
# 34116 Motor Housing Screw (small slotted or Phillips)
# 34217 Motor Mount Screw (stainless, w/o lift only)
# 34145 Motor Mount Screw (plastic, with lift only)
# 70232 Motor Housing Seal Tape (black)
# 06017 Pump Housing (with one support for ring)
# 95081 Pump Shaft Assembly
# 95368 Pump Motor 110 volt (with mounting hardware)
# 93025 Rotation Motor (two bearing-old only)
# 93026 * Rotation Motor (tapered shaft-new only)
# 95001 Rotation Magnet (for motor w/o lift only - old only)
# 95556 *Rotation Magnet (for motor w/o lift only - new only)
# 95523 Cog Gear (black, for motor with lift only - old only)
# 95555 * Cog Gear (black, for motor with lift only - new only)
# 94003 Transformer Circuit Board for CPA-2, 110 volt (old only)
# 94128 * Transformer Circuit Board for CPA-2, 110 volt (new only)
# 94004 Transformer Circuit Board for CPP-2, 110 volt (old only)
# 94135 * Transformer Circuit Board for CPP-2, 110 volt (new only)
# 95071 Switch Circuit Board for CPA-2 (old only)
# 94132 * Switch Circuit Board for CPA-2 (new only)
# 95114 Switch Circuit Board for CPP-2 (old only)
# 94136 * Switch Circuit Board for CPP-2 (new only)
# 94008 Display Circuit Board for CPP-2 (with temperature probe - old and new)
# 95066 Thermal Overload Reset (with probe)
# 26003 Heat Indicator Lamp for CPA-2, 110 volt
# 95178 Thermostat for CPA-2 (with probe)
# 93034 Heating Element, 110 volt (with mounting hardware)
# 27005 Fuse, 6.3 Amp, 250 Volt (rated), Type F (fast blow) for CPA-2 and CPP-2
# 27017 Fuse, 1.25 Amp, 250 Volt (rated), Type T (slow blow) for CPA-2 and CPP-2 (some old only)
# 27008 Fuse, 800 milli-amp, 250 Volt (rated), Type T (slow blow) for CPP-2
# 27009 Fuse, 1.6 Amp, 250 Volt (rated), Type T (slow blow) for CPA-2 and CPP-2 (new only)

Parts for the Tempering Bath:

# 3373 1000 ml Bottle, White
# 3372 1000 ml Bottle, Black
# 3381 1000 ml Bottle Set (4 white, 2 black)
# 05042 Cap for 1000 ml Bottle
# 3308 260 ml Graduate
# 3318 Graduate Kit (four #3308 graduates)
# 95520 Set of two Processor Leveling Wedges
# 15012 Ceramic Spacer (bottom of lower trough)
# 95322 Drain Valve Assembly
# 3321 Color Thermometer (CPA-2 only)

Parts for the JOBO Lift

# 07083 White Retaining Clip (old style lift only)
# 92157 Black Retaining Clip Assembly (new style lift only)
# 92158 Red Cap for Lift (new style lift only)
# 07109 Lift Handle Attachment (hub only)
# 95186 Lift Handle Assembly (includes hub, tube and cap)
# 34200 Screw for the Lift Handle
# 95200 Transfer Gear Set (2 sets)
# 34901 Washer for Transfer Gear (old style lift only)
# 95465 Grease Syringe (for lift gears)

Parts for the Roller Block

# 95215 Roller Block Assembly for Lift Arm
# 95183 Roller Block Assembly for Processor Trough
# 07067 Roller Extensions (angled arms) for roller block
# 07007 White Rollers for roller block
# 92167 Black Rollers with stainless steel axle for Expert Drums (substitute for 07007)

Parts for JOBO Film Tanks and Print Drums

# 03042 Funnel, light trap for 1500/2500 Film Tanks (2800 with stopper, lift only)
# 03046 Red Cap, for lid of 1500/2500/2800 series
# 03049 Beaker, for lid of 1500/2500/2800 Paper Drums
# 04043 Center Core for single reel with base (1510, 1540)
# 04044 Center Core for two reel with base (1520, 1526, 2521, 2523, 2551, 2553, 2563, 2583, 2593)
# 04045 Center Core for three reel extension (1526, 1530, 1540, 2553, 2560, 2563, 2583, 2593)
# 04073 Center Core for one reel extension (2563)
# 91034 Inversion Lid With Ring for 1500 series (no funnel, beaker, or cap)
# 91036 Inversion Lid With Ring for 2500/2800 series (no funnel, beaker, or cap)
# 1505 Cog (converts inversion lid to cog lid for use on lift)
# 07095 Cog Lid Washer (Red)
# 15042 Cog Lid Stopper (makes funnel #03042 a light trap for prints, used with lift)
# 1503 Cog Lid for 1500 series (with funnel)
# 2503 Cog Lid for 2500/2800 series (with funnel and stopper)
# 91033 Cog Lid for 3000 series (with permanently mounted funnel and stopper)

Go To:

1. Processor Specifications; CPA-2 and CPP-2

2. Safety First

3. Differences Between the CPA-2 and the CPP-2 Processors

4. Processor Description

5. Cleaning the Processor

6. Processor Maintenance and Tips

7. Processing Instructions for Film Using Magnet Drive

8. Processing Instructions for Prints Using Magnet Drive

9. Processing Using the JOBO Lift Accessory

10. Processing Instructions With the JOBO Lift Accessory

11. Precautions for Film and Paper Processing

12. Additional Processing Information

13. Spare Parts

14. Fuse Replacement